This is a list of miscellaneous tools for sale. Some of them will have a button to click to see a picture. Instead of having to load each image to continue, just scroll this list and click to see an image.

This section has Doweling Machines, Miscellaneous Wood Working Tools, including Jointer Fences, Metal Working, Caulking Irons, Wheelwright and Sheet-metal Tools

Back To Tool Index Back to Homepage

Wood Working Tools

No. 77 Doweling Machine and Cutters ... Click To Order

1. STANLEY NO.77, DOWELING MACHINE Comes with the 3/8 cutter. A really nice one. 98% of the black enamel remains. Note: The threads on the front screw are left-handed - that's why the toggle-screw gets so banged up or destroyed - so, to take it off, turn it the other way than usual. Very crisp. It has the original crate with a partial lable. Includes the original instructions, Fine+ ............. Sold $450.00
   Picture
   Picture

   Doweling Machine Parts Click To Order

2. STANLEY NO.77, DOWELING MACHINE: SET OF CUTTER HEADS, 1/4, 5/16, 7/16, 1/2, 9/16, 5/8, 11/16 and 3/4 inch. Almost of the black enamel remains. A couple of spots of rust but no pitting. The cutters have good length, but probably need some sharpening, Fine ............. Sold $1000.00
   Picture
   Picture

3. 5/16 INCH CUTTER HEAD, Has had little use. 95% of the black enamel remains. Has been lightly cleaned, Fine ............. $135.00
   Picture

Other Woodworking Click To Order

1. STANLEY NO. 89 CLAPBOARD GAUGES (pair). Use them to hold clapboard siding in place for measurement and nailing. 95% nickel plating. The gauge slips under the siding board below, and locks into place to hold the current board. Move the handle sideways for a spur to lock them in place, Fine ........... Sold $75.00
   Picture

2. STARRETT NO. 111 STAIR GAGE FIXTURES, They fit on any framing square and are used to layout stair stringers and rafter cuts. Most of the nickel plating remains, G++ ........... Sold $20.00
   Picture

3. L. & I. J. WHITE, TURNING GOUGE, 1 1/8 inch wide. There's a short split in the handle, G++ ............. $50.00
   Picture

4. DELTA NO. 130 TURNING TOOL SET, Eight tools in the original box, which has some tape on the edges. Some minor stain, Fine ............. $90.00
   Picture

5. Boxed STANLEY NO. 185 BURNISHER, Use this one to turn the edge on scraper blades. Looks brand new. In its original box, Fine+ ...... $80.00
   Picture

6. NEW YORK KNIFE CO.,TIMBER SCRIBE, Hammer Brand. Folding rosewood handle has an initial M carved in it, G+ ......... $50.00
   Picture

7. DEXTER LAYOUT KNIFE. Bronze with rosewood handle. Marked blade is 8 3/4 inches long, G+ ......... $30.00
   Picture

8. STANLEY NO. 203, BENCH BRACKET, Used to hold the other end of a long board to the edge of a work bench. To attach to a bench, the jaw or nose, is put through a hole in the bench front and is automatically held in place. The screw clamp firmly holds the work in place. 95% japanning. Pat 3-16-(19)15 stamped on the thumbscrew, Fine ............. Sold $60.00
   Picture

9. STANLEY NO. 203, BENCH BRACKET, Used to hold the other end of a long board to the edge of a work bench. To attach to a bench, the jaw or nose, is put through a hole in the bench front and is automatically held in place. The screw clamp firmly holds the work in place. 95% japanning. Pat 3-16-(19)15 stamped on the thumbscrew, Fine ............. $60.00
   Picture

10. Boxed STANLEY NO. 207, BENCH STOP, Sweetheart logo. A tool that will immediately be useful to the carpenter, cabinetmaker or anyone interested in woodworking of any kind where a bench is necessary. It can be inserted in the top of a bench by boring a 9/16-inch hole. Its height is adjustable-a stiff spring holds it in position.
    Blued finish, probably from WW II. Some damage to the label, Fine ............. $40.00
    Picture

11. STANLEY NO. 207, BENCH STOP, Sweetheart logo. A tool that will immediately be useful to the carpenter, cabinetmaker or anyone interested in woodworking of any kind where a bench is necessary. It can be inserted in the top of a bench by boring a 9/16-inch hole. Its height is adjustable-a stiff spring holds it in position. Has some tarnish, G+ ............. $25.00
    Picture

12. STANLEY NO. 386, JOINTER FENCE, 4-1-(19)13 patent date cast in the frame. Sweetheart logo on the adjusting bar. Complete and entirely functional. 90% of the nickel plating remains (somewhat worn on the bottom), G++ ........... Sold $175.00
    Picture

13. THE ALEXANDER ADJUSTABLE JOINTER GAUGE, Patented July 16, 1872. Fits on any wooden plane - jack to jointer. This one isn't marked, but they were sold by Millers Falls. Has screws to attach it to a plane, G+ ........... $60.00
    Picture

14. STANLEY NO. 28 CORNERING TOOL, Sweetheart logo ... Cuts 1/16 and 1/8 inch radius corners on the edge of a board. Allmost all of the nickel plating remains, Fine ........... $25.00
    Picture

15. STANLEY NO. 29 CORNERING TOOL, Sweetheart logo ... Cuts 1/4 and 3/8 inch radius corners on the edge of a board. Not nickel plated, may be WWII, G+ ........... $20.00
    Picture

16. CRESCENT TOOL CO. GIANT NO. 1 NAIL PULLER. Very useful for pulling nails when working on an old house. 90% paint remains, Fine ........... $35.00
    Picture

17. WOODEN VISE HANDLE, 7/8 inch diameter, 15 inches long. The ends slip off to install, G++ ........... $10.00
    Picture

18. HARD ARKANSAS OIL STONE. Five inches long. In its original wooden box, G++ ........... Sold $30.00
    Picture

1. P. S. & W. "HANDY" SEAMER. 3 1/2 inches wide and adjustable from 1/16 to 3/4 inch. Bends the edges of sheet metal. Useful for work in tight places, or, if you don't have anything else - To bend edges when assembling ductwork for your furnace, G+ ........... Sold $30.00
   Picture

2. BENCH SHEARS. Not marked by Mfr. 30 inch length. 7 inch jaws. Fits in the hardy-hole on your anvil or in a bench plate. Crisp. Missing some of the enamel, but, Fine ........... $85.00
   Picture

3. Boxed GREENFIELD TOOL & DIE CORP. NO. 13 O.K. JUNOIR ADJUSTABLE GUIDE STOCK. Holds 13/16 round dies. Has a 1936 patent number. This is the small, good one that has a built-in guide. Six inches long. Comes with 6-32, 8-32, 10-32, 1/4-20, and 5/16-18 dies. The tool is great, some oil and wear to the box, Fine ........... $40.00
   Picture

4. GOODELL PRATT HAND VISE. Has parallel jaws 1 3/16 wide, G+ ........... $30.00
   Picture

5. GRUV GRIP, 3/32 inch STEEL LETTERS AND NUMBERS SET. Young Bros. Stamp Works, Muscatine, Iowa. They have a groove in the side to show which way is up, Fine. Complete, and have seen little use, Fine ........... $75.00
   Picture

6. BERG NO. 528, ESKULSTUNA, SWEDEN, Diagonal cutters. 4 1/2 inch length. For piano wire, G++ ........... $35.00
   Picture

7. CRAFTSMAN, DRILL INDEX. For number drills, 4 1/2 inches long. No. 1 through 60. Cast metal, G++ ........... $30.00
   Picture

8. Boxed GOODELL PRATT NO. 663 BENCH VISE, Black enamel. Jaws are 1 1/2 inches wide. The box has some wear, Fine+ ........... $100.00
   Picture

9. STANLEY No. 663 BENCH VISE, Black enamel. Jaws are 1 1/2 inches wide, 4 inches long, G++ ........... $40.00
   Picture

10. PIN VISE, An early one with an Aug. 10, 1875 patent date. I can't remember who made it. 4 inches long, G+ .... Sold $30.00
    Picture

11. MOHAWK VISE, No. 60. 2 1/2 inch jaws, 5 1/2 inches long, G++ .... $40.00
    Picture

12. STANLEY No. 701 BENCH VISE, Sweetheart logo. 1 1/2 inch jaws, 5 1/2 inches long. Has some rust and light pitting, G ......... $35.00
    Picture

13. STANLEY NO. 710 VISE, in orange and black paint. It's useful to have one that swivels on it's base, which lets you work from different angles. It has 2 1/2 inch jaws, and is ready to go to work G+ ........ $65.00
    Picture

14. TOP & BOTTOM SWAGE, 2 INCH Quikwerk. 1 inch tang. Two corners of the bottom are slightly rounded, New-old stock. ............. $70.00
    Picture

15. TOP & BOTTOM SWAGE, 3/4 INCH Beall Bros., Iron City. 5/8 inch tang. New-old stock. ............. $70.00
    Picture

16. BOTTOM FULLER, 1 inch tang. 1 inch across the diameter. Has some pitting, G ............. $30.00
    Picture

1. T. LAUGHLIN, PORTLAND, ME. CAULKING IRON, 2 3/8 inches wide, very thin blade, G+ ....... $40.00
   Picture

2. C. DREW & CO. CAST STEEL CAULKING IRON, 2 1/2 inches wide. One crease? (about 1/8 inch), G++ ....... Sold $40.00
   Picture

3. CAULKING IRON, Unmarked by mfr. Three crease (1/4 inch). 1 3/4 inches wide. One of the side ridges is damaged at the end 3/16 inch by pitting, G ....... $35.00
   Picture

Wheelwright and Sheet-metal Tools
Click To Order

1. TRAVELLER, Hand wrought - about 9 inch diameter. Some rust and light pitting, but still usable, G .... $40.00
   Picture

2. TRAVELLER, Hand wrought - about 8 inch diameter. Hand-forged. Curved spokes and a pointer. Some rust and light pitting, but still usable, G .... Sold $40.00
   Picture

3. TRAVELLER, Hand wrought - about 8 inch diameter. Hand-forged. Very wide circle. Some rust and light pitting, several checks in the handle, G .... $40.00
   Picture

4. HUB BORER, It's rusty and I don't see a Mfr. mark. 40 inch overall length. Missing the crank handle and cutters. You probably have references that show how to use it, and make the missing parts, G ... Sold $100.00
   Picture

5. PECK, STOW & WILCOX, IMPROVED WOOD ROOFING FOLDER WITH GAUGE. Used for fitting standing seam roofing.
   After cutting corners, turn lock on ends of the sheet. Then place the sheet in the folder with lock down in the slot of the plate, which will bring opposite lock in the slot in the wood at the end of the plate.
   It looks like it is for sheets 26-27 inches long for the locks to fit in the slots. There are two holes in the bottom wood frame. There is a 6 inch split from the end through the one hole, which will need a bit of repair, G+ .... $65.00
   Picture

1. LEATHER ROUNDER. Used to round leather for reins, etc. Holes from 1/4 to 1/2 inch. Eight inches long, G+ .... Sold $75.00
   Picture

2. GEO. BARNSLEY & SONS, SHEFFIELD, ENGLAND ROUND KNIFE. 5 1/2 inch diameter blade, G++ .... Sold $40.00
   Picture

Back To Tool Index Back to Homepage