BARGAIN BIN

This is an assortment of user tools for sale. Some of them will have a button to click to see a Picture. ... Instead of having to load each image to continue, just scroll this list and click to see an image. This is a list of tools for sale, which for various reasons are good deals.

Note: I have Ordering Instructions. Just click on Click To Order in any section, or right here.

Back To Tool Index Back to Homepage

Planes [Click To Order]
  1. STANLEY NO. 40 SCRUB PLANE, T trademark on the cutter with good length. The japanning is worn. Someone replaced the handle and knob that aren't Stanley but they fit, Good .......... Sold $50.00
    Picture
    Picture - Sole

  2. STANLEY NO. 220 BLOCK PLANE, It has an adjustable cutter. An early one with the V trademark on the cutter with good length. Looks like it has been repainted. Has the 10-12-(18)97 patent date on the cap. Some roughness on the sole, G+ .......... $30.00
    Picture
    Picture - Sole

  3. STANLEY NO. 18, BLOCK PLANE, An earlier one from the 1890s. Large J half-circle trademark on the cutter. with good length. Early knuckle-joint lever cap. Adjustable throat is very nice. Some light pitting on the sole. A great user, G ........... Sold $30.00
    Picture
    Picture - Sole

  4. STANLEY NO. 220 BLOCK PLANE, 6 inches long. Notched-rectangle logo on the cutter. Adjustable cutter. A later US production with almost all of the maroon enamel, G++ .......... Sold $25.00
    Picture
    Picture - Sole

  5. STANLEY NO. G12-060 BLOCK PLANE, A late No. 60 made in England. Adjustable throat and cutter. Has had little use, G++ .......... Sold $20.00
    Picture
    Picture - Sole

  6. STANLEY NO. 80 SCRAPER PLANE. Sweetheart logo on the crossbar. Has 90% of the japanning. Some patina on the bare-metal surfaces. It has had some finish added to the surface for protection. The cutter is cut down from some other plane or scraper life. It is a little thicker than a normal No. 80 cutter. A great user, G .......... Sold $30.00
    Picture
    Picture - Sole

  7. STANLEY NO. 7C, JOINTER PLANE, 22 inches long. Sweetheart logo on the cutter, which has some pitting at the top but is good at the edge. The tip of the handle is missing and it needs some cleaning, but it will be a good user, G .......... Sold $50.00
    Picture
    Picture - Sole

  8. STANLEY GAGE NO. 5C JACK PLANE, Complete. Missing most of the japanning. Decent wood, G ...... Sold $40.00
    Picture
    Picture - Sole

  9. CRAFTSMAN (SEARS)) NO. 78 RABBET & FILLETSTER PLANE. Made by Millers Falls. Later one with the cutter adjusting lever. Good cutter. Complete with spur, fence and depth stop. 90% japanning. Has some rust that can use some cleaning, G+ .......... $50.00
    Picture
    Picture - sole

  10. MILLERS FALLS NO. 65 BLOCK PLANE. (Stanley No. 103) 80% japanning with a bit of dirt, This short one has the cutter-adjustment lever, G+ .......... $20.00
    Picture

  11. SARGENT NO. 306, BLOCK PLANE, 6 inches long - like a Stanley No. 9 1/2 but with nickel plated trimmings. Has a Craftsman blade,(which is missing the little lateral-adjust lever) so, it was probably sold by Sears. 95% japanning, pretty good nickel plating, G++ .......... Sold $20.00
    Picture

Miscellaneous [Click To Order]

  1. BEVEL, Rosewood and brass, 10-inch. Unmarked but probably made in England, G+ ............ $20.00
    See Picture

  2. MEASURING LOT NO. 1. Millers Falls 8-in bevel, Stanley scratch awl, North Bros No. 45 push drill w/ all 8 bits in good condition, General stair gauges for framing square, Stanley trammel points, G and Better ........ Sold $50.00
    Picture

  3. MEASURING LOT NO. 5. Stanley scratch awl, Twix offset bevel (about 5-inch blade), inside caliper, Lakeside center-finding punch, G+ ........ $40.00
    Picture

  4. MEASURING LOT NO. 4. Outside caliper marked Pat. Apr. 15, 1915, inside caliper - Athol Mach.Co, Dividers - Union Tool Co, D. B. & S.2-inch square, with some pitting on the blade, 7-inch dividers, Thewlis registering caliper, Kraeuter 4-inch hermaphrodite caliper, G to G+ ........ $50.00
    Picture

  5. MEASURING LOT NO. 3. Stanley 47-061 marking gauge, Stanley No. 20 6-inch try-square ( looks WW II, unused w/ cosmoline, but some wear to the finish on the handle), Stanley scratch awl, and Craftsman stair gauges for a framing square, and a Hold-E-Zee screw-holding screwdriver, G+ to Fine ........ $50.00
    Picture

  6. DOUBLE SPOKE SHAVE, Has both a flat and convex shave side-by-side. The top of the cutters have some pitting, and I can't quite read logo. The sole and the bottom edges of the cutters are very nice for use, G ................ Sold $20.00
    Picture
    Picture - Bottom

    P. S. & W. NO. 8012 BRACE, 12 inch sweep. This is an early top-of-the-line Pexto company brace. June 9, 1895 patent date on the Samson patent ball-bearing chuck holds tanged bits up to No. 2 Clark's Expansion bit, and and any shank 1/8 to 1/2 inch in diameter. Open, positive ratchet. Rosewood head - full steel clad and screw fastened, and handle with friction washers. The nickel plating is worn in places. The workings are still tight and it will be a great user, G+ ........... Sold $40.00
    Picture

  7. STANLEY NO. 921-8 IN BRACE, Eight-inch sweep. A top-of-the-line brace with enclosed chuck and the ball-bearing stuff. Rosewood handle and pad. Completely functional, but has some patina from age and use, G .............. $35.00
    Picture

  8. STANLEY NO. 397, SUREFORM 10-Inch Convex PLANE, Fine cut. New old stock. Box has one end ripped off. Includes instructions, Fine ................ Sold $20.00
    Picture

  9. STANLEY NO. 44, CIRCULAR GUIDE for use with NOs. 20-25-30 and 40 ROUTER SHAPERS. I don't do power tools, but I got this. I don't know if it is an accessory or replacement part. Maybe someone is dying for one.... New in the box ................ $15.00
    Picture

  10. STANLEY NO. 95 BUTT GAUGE, Used for laying out door hinges and strikes. Original box is rough, G+ ............ Sold $25.00
    Picture

  11. MILLERS FALLS NO. 104, HAND DRILL, Three-jaw chuck holds any round bits from 0 to 3/16. Stained hardwood handle is hollow to hold bits, but they are missing. 11 1/2-inches overall length, G+ ............... Sold $25.00
    Picture
    Picture - Back

  12. BROAD AXE HEAD.Only mark is J20. The edge is 12-inches wide. Has some rust, G ....... Sold $45.00
    Picture
    Picture - Back

  13. E. C. STEARNS SAW VISE. Wentworth pattern with 10 1/2-inch jaws. Cam action adjustment. Made to screw on the side of a bench, or on a board to put in your vise. Has some light rust and a bit of dirt, G+ ......... Sold $25.00
    Picture

  14. LUTHER BROS. CHUCK EXTENSION. Eight-inches overall. Apparently for hard-to-reach work where you can't operate your brace, G+ ........ Sold $20.00
    Picture

  15. DISSTON KEYSTONE K-4 BACK SAW, 14-inches. 13 ppi. Apple wood handle. Straight and kind-of sharp, G+ .......... Sold $40.00
    Picture

  16. CRAFTSMAN BACK SAW, 16-inches. 12 ppi. Has owner's name and 1970 date etched along the top. Some green paint on the handle. Straight and sharp, G+ .......... Sold $30.00
    Picture

  17. GREENLEE 3-INCH SLICK. Actually, a very nice slick with a broken handle. The blade is 9 3/4- inches. There are a couple of very tiny nicks on the edge. I have other slicks on my Edge Tools List , G++ ....... Sold $70.00
    Picture
    Picture

  18. BENCH STOP (1), 7 3/4 inches long. Has a long spring on the side and fits into a 7/8 square hole in a bench. I have other bench stops on my Miscellaneous Tools List , G+ ......... Sold $20.00 Each
    Picture

  19. BENCH STOP (2), 7 3/4 inches long. Has a long spring on the side and fits into a 7/8 square hole in a bench. I have other bench stops on my Miscellaneous Tools List , G+ ......... Sold $20.00 Each
    Picture

  20. "YANKEE" NO. 45, PUSH DRILL, Has all eight bits from 1/16 to 11/64ths,which are in nice condition but may need a touch-up sharpening. - the 1/16 is a little short, G ......... $20.00
    Picture

  21. NORTH BROS. "YANKEE" NO. 41, PUSH DRILL, Has all eight bits from 1/16 to 11/64ths, which are in nice condition but may need a touch-up sharpening. Some of the nickel plating is worn or missing, G+ ......... Sold $25.00
    Picture

  22. TORPEDO LEVEL. Nine-inch. Rosewood and brass, probably English. The plumb vial has been replaced and not accurate, G ........... $20.00
    See Picture

  23. STARRETT 12-inch rule with center finder. Owner's mark on rule, G+ ................ Sold $20.00
    Picture

  24. STANLEY NO. 63 SPOKE SHAVE. Light-duty one with curved sole. Sweetheart logo on the 1 3/4 inch cutter with good length. 50% japanning with some patina on the bare-metal surfaces, G .............. $25.00
    Picture
    Picture - Sole

  25. C.E. JENNINGS 1/4-INCH SOCKET FIRMER CHISEL, 5-inch blade, 11 1/4-inches overall. Replaced handle, G ....... Sold $15.00
    Picture

  26. UNION HARDWARE CO. 1 in. SOCKET FIRMER CHISEL, 6-inch blade, 12 3/4-inches overall. Chip on edge. Replaced handle, G ....... Sold $20.00
    Picture

  27. ROBERT SORBY, 2 in. TANGED FIRMER CHISEL, 4 1/2-inch blade, 12-inches overall. Split in the ferrule and missing some of the cushion, G+ ....... Sold $25.00
    Picture

  28. CRAFTSMAN NO. 2 HAND DRILL. Made by Millers Falls. This one's the large size, 14 1/2 inches long. A strong, serviceable tool built on a sturdy cast frame. Three-jawed chuck with protected spring holds 0 to 3/8 round shank bits. Spindle equipped with ball thrust bearings. Tropical hardwood handle and knobs are nice with wear to the finish. The handle unscrews to hold bits, there are five remaining. You can use regular twist drills. It could use a bit of cleaning, G+ ...... Sold $40.00
    Picture
    Picture - Back

  29. BRASS PLUMB BOB, The box label says 16oz. Unmarked by mfr. Has some minor dings, G++ ........ $20.00
    Picture

  30. HOOK SCRAPER CO. NO. 75 SCRAPER. Wood body with three extra blades, Fine ........... Sold $20.00
    Picture

  31. STANLEY NO. 18, 10-inch BEVEL SQUARE. Not much nickel plating. A bit of pitting on the back end of the blade. Great user, G ............Sold $15.00
    See Picture

  32. 8- INCH MITER SQUARE, English. Ebony and brass handle with owner's name, G ............ Sold $20.00
    See Picture

  33. STANLEY NO. 200 SHARPENING GUIDE. For chisels and plane blades to get the proper bevel. It could use a light cleaning, G+ ........ Sold $50.00
    Picture

  34. STANLEY NO. 73 MORTISE GAUGE, Boxwood and brass. A little shorter than the other numbers at 6 inches long. Graduations to three inches for the slide. The adjustable mortise point has been filed down, so it's now a marking gauge, G+............ $25.00
    Picture

  35. CRAFTSMAN Spiral Ratchet Screwdriver. Made by MILLERS FALLS. It spirals to drive a screw, and is reversible. The largest size, like the Stanley 31, 14 1/2 inches long closed. It has a 1/4 inch bit,and a No. 3 philips bit. They are Yankee, but interchangeable, G+ .......... $20.00
    Picture

Back to Homepage Back To Tool Index